What Does Code P0010 Mean?
The variable valve timing (VVT) system increases fuel economy and engine performance by regulating when the intake and exhaust valves are opened and closed. The camshaft(s) is(are) adjusted by the Engine Control Module (ECM) through the use of an oil control valve(s) (OCV) also called variable valve timing control solenoid valves. Code P0010 is triggered when the ECM attempts to adjust the Bank 1 intake camshaft timing by utilizing one of these valves, and it detects an electrical issue in either the circuit going to the valve or the windings of the solenoid in the valve itself. Show P0010 CausesThere are many potential causes of code P0010.
P0010 Symptoms
How Do I Fix Code P0010?With a VVT fault, the first step is to get it diagnosed to figure out what is causing the problem. If your vehicle has this fault and you’re not comfortable diagnosing this issue at home, we recommend finding a RepairPal certified shop nearby to pinpoint the problem and give an accurate estimate for repairs. These shops can not only help you figure out what’s going wrong before you waste time and money on the wrong parts, but they also offer a minimum 12-month, 12,000-mile warranty and stand behind all their estimates with guaranteed fair pricing. > Find a RepairPal Certified Shop Near You How Much Does It Cost to Fix Code P0010?P0010 can be caused by anything from a bad VVT solenoid to failed sensors to old engine oil. It’s impossible to give an accurate estimate without properly diagnosing the issue first. If you take your car to a shop for diagnosis, most shops will start with an hour of “diag time” (the time spent in labor diagnosing your specific issue). Depending on the shop’s labor rate, this typically costs somewhere between $75-$150. Many, if not most, shops will apply this diagnosis fee to any required repairs if you have them perform the repairs for you. From there, a shop will be able to give you an accurate estimate for repairs to fix your P0010 code. Possible Repair Costs for P0010For error code P0010, one or more of the below repairs may be needed to solve the underlying issue. For each possible repair, the estimated cost of repair includes the cost of the relevant parts and the cost of labor required to make the repair.
DIY Steps to Diagnose Code P0010Engine code P0010 could be caused by a number of things, including a bad VVT solenoid, a bad sensor, or even dirty oil. If you’d like to try to fix code P0010 at home without throwing money at parts, you’ll want to follow the steps below for proper diagnosis. Keep in mind this is an intermediate-level diagnosis and repair and not recommended for beginners. Diagnosis requires more specialized equipment beyond what the FIXD Sensor can provide and it can be a time and labor-intensive process for inexperienced DIYers. DIY difficulty level: Intermediate This repair requires mechanical knowledge and is not recommended for beginners. Tools/parts needed (our top picks from Amazon):
STEP 1: USE FIXD TO ENSURE NO OTHER ENGINE CODES ARE PRESENT.Use FIXD to scan your vehicle to verify P0010 is the only code present. STEP 2: CHECK VVT CONTROL SOLENOID VALVE.Do a visual inspection of the bank 1 variable valve timing (VVT) control solenoid valve. Make sure to repair any frayed or faulty wiring or connectors. Once you have done this, clear the code and rescan to see if it is still present. STEP 3: CHECK FOR ENGINE SLUDGE.Check to see if there is any engine sludge present. This can gum up the VVT control solenoid valve and prevent proper operation. If it’s dirty, clean it, clear the code, and rescan to see if it is still present. STEP 4: CHECK VVT SOLENOID RESISTANCE.Perform a resistance check of the bank 1 intake camshaft VVT Control solenoid and compare it to the vehicle service manual. If it is out of spec, replace the bank 1 intake VVT Control Solenoid. If the code is still present after these steps, you may need to bring your vehicle to a mechanic for further guidance. Common P0010 diagnosis mistakesA common diagnosis mistake associated with code P0010 is replacing the timing actuator without first attempting to clean the actuator or check the electrical circuit to see if that was the actual issue. Still Need Help Fixing Code P0010?If you’ve followed the steps above and are still experiencing check engine code P0010, please contact the FIXD Mechanic Hotline if you’re a FIXD Premium subscriber or find a RepairPal certified shop near you to get the right repairs at a fair price. Popular Engine Codes p0420 code p0172 code p00171 code p0128 code p0300 code p0456 code p0430 code p0442 code p0455 code p0113 code  Recovering autocross and track day enthusiast. Once turned a VW Jetta into a pickup truck. Lives in a van down by the river. Dream car: 2001 Subaru WRC rally car. Where is camshaft position sensor a bank 1 located?A camshaft position sensor (CMP) is essentially a component in the format of a cylinder, which is often located on the outside of the front cover (at the front of the engine under the valve cover).
What would cause a P0010 code?The most common cause of a P0010 DTC is a faulty VVT control solenoid valve, which causes improper opening and closing of the intake and exhaust valves. Another common cause of this DTC is contaminated oil sludge in the engine. Your crankshaft or camshaft position sensor may also be malfunctioning.
Can I still drive with P0010 code?The DTC P0010 is moderately severe, meaning it won't make your car unsafe to operate. So yes, you can drive your car. However, with time, it will lower fuel economy and reduce power. But most importantly, your vehicle will fail the emissions test.
|
P0010 a camshaft position actuator circuit open bank 1
Copyright © 2024 en.apacode Inc.
