Problems with gauge cluster and power locks. Recently, I disassembled the dash on my 2001 Cherokee Sport in order to replace the evap and heater cores. Everything seemed to be fine for about a week. Then, one day, the door locks stopped working. I replaced both modules with new ones, still didn't work. At the same time, I got the NO BUSS signal, and noticed that when I turned the headlights on, the tac and fuel gauge dropped off and the air bag light came on. When I tried the unlock/lock button on the DDM the horn honks and the rear defroster switch light comes on as well as the shift indicator lights. The windows seem to work fine. I have cleaned the cluster gauge contacts (several times), checked for broken wires to the DDM & PDM, checked fuses, grounds, etc.. Does anyone know what I'm missing? My next step is a new instrument panel connector. Quote: Originally Posted by ribich22  ...... went to turn it on and it fired up and then died after about a second and a half. This is a common symptom when the factory anti-theft system (SKIM) is misbehaving. The SKIM indicator light is a key symbol inside a slashed circle in the upper left hand side of the cluster. Think No Parking, but with a key symbol instead. Thicker keys with a light gray color are a sign that your Cherokee has the SKIM. Google or search Quote: Originally Posted by ribich22 ..... The needles on the gauges are not moving. .... on the odometer it is showing "no bus" and the tranny light is on too. The No-Bus and gauge problems point to a a CPS problem. Test the CPS and inspect the wire harness. The most likely cause of it cranks and cranks but won't start up is the Crankshaft Position Sensor (CPS) located on the transmission bell housing. Often this part is also referred to as the CranKshaft Position Sensor (CKP) CPS/CKP failure is very common. The CPS/CKP can stop working with no warning or symptoms and the engine will not run or the engine may randomly stall for no apparent reason. Begin with basic trouble shooting of the start and charge systems. Remove, clean, and firmly reconnect all the wires and cables to the battery, starter, and alternator. Look for corroded or damaged cables or connectors and replace as needed. Do the same for the grounding wires from the starter to engine block, and from the battery and engine to the Jeep's frame/body. Jeeps do not tolerate low voltage or poor grounds and the ECM/ECU may behave oddly until you remedy this. Symptoms – If the CPS/CKP is failed sometimes the OBD-II trouble code reader cannot make a connection to the ECU/computer or cannot read Check Engine Light/MIL codes because the CPS/CKP has failed. Disconnect the code reader, disconnect the CPS/CKP wire connector, and reconnect the code reader. If the code reader establishes contact with the ECU and scans, your CPS/CKP is failed and needs to be replaced. Crank Position Sensors can have intermittent “thermal failure”. This means that the CPS/CKP fails when the engine gets hot, but works again (and will test as “good”) when it cools back down. Diagnostic steps to confirm the CPS is the cause of your no-start You should be able to verify a bad cps, by unplugging it, and turning the ignition key to on. If the voltage gauge and/or the fuel gauge now displays correctly and/or the No-Bus is gone, replace the CPS. If the CEL does not come on when the key is turned to the RUN position... then the CPS/CKP is bad. Unplugging and reconnecting the CPS sensor where it connect to the main harness near the back of the intake manifold usually resets the ECU and if the jeep fires right up after doing this you can bet that the CPS is faulty and needs to be replaced. The 2000 and 2001 will have the CPS in the same location on the bell housing, but the wire connector is near the Transfer Case, not as shown in the diagram below. Simply follow the wire from the sensor to the connector. Exchange the fuel pump relay and the ASD relay with one of the other similar ones in the PDC to eliminate the relays as the cause of the no-start. Check the ASD relay fuse. Confirm that the fuel pump to runs for 3-5 seconds when you turn the ignition key to ON. Eliminate the NSS as a cause of no start. Wiggle the shift lever at the same time you try to start. Put the transmission in Neutral and do the same. Do the reverse lights come on when the shifter is in Reverse? Inspect the wires and wire connectors at the O2 sensors on the exhausts pipe. A short circuit from melted insulation or from broken O2 sensor wires can blow a fuse and the ECU/ECM will loose communication. Don’t get tunnel vision and assume the sensor is bad (unless it tests bad with a meter). Damaged wiring or a dirty connector can inhibit the signal from making it to the computer. Inspect/test/clean/repair wiring or connectors as necessary. CPS Testing Crankshaft Position Sensor Connector (CPS/CKP)
. TESTING PROCEDURE 1991 – 2001 4.0L H.O. engines 1. Near the rear of intake manifold, disconnect sensor pigtail harness connector from main wiring harness. TESTING PROCECURE for 1987 – 1990 4.0 L engines Test # 1 - Get a volt/ohm meter and set it to read 0 - 500 ohms. Unplug the CPS and measure across the CPS connector's A & B leads. Your meter should show a CPS resistance of between 125 – 275 Ohms. . If the CPS is out of that range by much, replace it. Test # 2 - You'll need a helper for this one. Set the volt/ohm meter to read 0 - 5 AC volts or the closest AC Volts scale your meter has to this range. Measure across the CPS leads for voltage generated as your helper cranks the engine. (The engine can't fire up without the CPS connected but watch for moving parts just the same!) The meter should show .5 - .8 VAC when cranking. (That's between 1/2 and 1 volt AC.) If it's below .5vac, replace it. . . . |
2000 jeep cherokee no bus instrument cluster not working
Related Posts
Copyright © 2024 en.apacode Inc.
