Show
Estimate price near meIncluded for free with this service 12-month / 12k-mile warranty Free 50 point safety inspection Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.
How much does a Camshaft Position Sensor Replacement cost?On average, the cost for a GMC Acadia Camshaft Position Sensor Replacement is $184 with $32 for parts and $152 for labor. Prices may vary depending on your location.
Show example GMC Acadia Camshaft Position Sensor Replacement prices What is the Camshaft Position Sensor all about?The camshaft position sensor monitors the position of the camshaft and reports that data to the car’s onboard computer system. This computer system works with sensors and other devices to keep the engine running. With data from the camshaft position sensor (CPS), the fuel injectors know when to fire. When the sensor malfunctions, the computer does not know when to fire the injectors and may not fire them at all. The faulty readouts may also throw off spark timing, which will affect the car’s fuel economy. This sensor is used in conjunction with the crankshaft position sensor to control ignition timing. It is common for heat and oil leaks to cause this sensor to fail, due to where the sensor is located. Keep in mind:
How it's done:
Our recommendation:The camshaft position sensor isn’t checked in most regular services, but your vehicle has warning signs for when the sensor begins to fail. Because it sends information to the camshaft, when the sensor begins to fail your engine will begin to have trouble. Your engine may have a hard time turning on, staying on, idling, or running smoothly. Your Check Engine warning light should illuminate as well. What common symptoms indicate you may need to replace the Camshaft Position Sensor?
How important is this service?The camshaft position sensor provides valuable information about the camshaft position to the computer management system. The computer system uses the information from the position sensor to determine when to inject more fuel. Without the sensor’s information, the computer won’t inject fuel properly, and your vehicle will stall or sputter. Fast and easy service at your home or office Backed by 12-month, 12.000-mile guarantee Recent articles & questionsHow to Buy a Good Quality Cylinder Head The The cylinder head is one of the single most critical parts of your car’s mechanics, and one part that can trigger the most engine damage if it becomes compromised. The cylinder head, along with the head gasket, sits on... Vehicle won't start after I switched the ECM.Hi there. First check the battery cables and make sure that they are clean and tight. Then check all of the sensors and make sure that all of them are connected. Then check the ECM and make sure that the... what sends signal to a TPS sensorHello, thank you for writing in. The throttle position sensor does not take inputs from anything, but instead it acts as an input to the ECU (the main computer). The ECU then uses it for engine performance. The sensor's resistance... Can't find crank shaft sensor 2011 dodge caravan crew 3.6 flex fuelYou sound like you are describing two possible problems. Sometimes the engine will not turn over and other times it turns but will not start up and run. If you have to sometimes put it in neutral to get it...
Are Bank 1 and Bank 2 camshaft sensors the same?Q: Are bank 1 and bank 2 sensors the same? Bank 1 and bank 2 have similar sensors. However, bank 1 has two sensors, of which sensor 1 is located near the engine before the catalytic converter, an upstream sensor called pre-CAT, and sensor 2 is located after the catalytic converter called post CAT, a downstream sensor.
Where is the camshaft position sensor located?The Camshaft Position sensor is typically located in the cylinder head of the engine and has a cylindrical portion that inserts into the head. The Crankshaft Position sensor is normally located in the timing cover or on the side of the block with a cylindrical portion that inserts into the block.
What are the signs of a failing cam sensor?A glowing check engine light, stalling, poor acceleration and bad fuel mileage are all possible signs your camshaft position sensor may be failing. Gone are the days of carburetors and distributors, replaced by a variety of sensors that help a car's computer get the maximum performance out of the engine.
|
2010 gmc acadia camshaft position sensor location
Related Posts
Copyright © 2024 en.apacode Inc.
