ModifiedLife March 27, 2012 at 9:21 pm Greg, as much as we would like to assist you, most of the radio wire info listed on our website is submitted by our visitors. We currently do not have any information on the 2011 Jeep Wrangler wiring but hopefully someone from our knowledgeable Modified Life community would be able to help you out. Reply Copyright ©1996-2022, Crutchfield New Media, LLC. All rights reserved. Crutchfield is a servicemark of Crutchfield Corporation. Sales tax informationCrutchfield collects state sales tax on items shipping to the following states: AK, AL, AR, AZ, CA, CO, CT, DC, FL, GA, HI, IA, ID, IL, IN, KS, KY, LA, MA, MD, ME, MI, MN, MS, NC, ND, NE, NJ, NM, NV, NY, OH, OK, PA, RI, SC, SD, TN, TX, UT, VA, VT, WA, WI, WV, WY. In other states where we don't collect sales tax, it may be the customer's responsibility to assure that all appropriate state use taxes are paid. JK Electrical, Lighting & Sound Systems Bulletin board forum regarding topics such as stereo head units, CD players, MP3 players, speaker systems, amplifiers, hardmounted GPS devices, computers, headlight upgrades, fog lights, off-road lights, general wiring and anti-theft devices. Radio wiring diagram JK Newbie Thread Starter
Join Date: Feb 2017 Location: Troy, ID Posts: 13 Likes: 0 Received 0 Likes on 0 Posts Hello, I am trying to wire an after market radio which has several wires (front, back, left, right, etc) but the wires that were in my oem radio harness only number 8. They are as follows: Thanks for any insight. I have found the obvious ones, Red = ACC and Black is ground. Yet when I plug these into the corresponding wires on the new stereo, It does not power on. It has a wire for battery and acc, but I don't think there is a battery wire in the oem wires. JK Newbie Thread Starter
Join Date: Feb 2017 Location: Troy, ID Posts: 13 Likes: 0 Received 0 Likes on 0 Posts The adapters do not fit the new stereo. At some point I will need to wire and I'd rather just do it directly. JK Newbie Thread Starter
Join Date: Feb 2017 Location: Troy, ID Posts: 13 Likes: 0 Received 0 Likes on 0 Posts I have made some progress. By plugging both stereo power wires (ACC & Battery) into the one power wire from the oem harness, I am getting the new stereo to power up. But I cannot get the sound wired right. I'm not sure if the oem set up used a common ground for the speakers or what, but I am left with a black wire (ground) a white and white/orange wire (bus wires) and 4 speaker wires. But no combination of connections to the speaker wires produces sound. JK Newbie
Join Date: Feb 2017 Location: Phoenix Posts: 29 with the Rubicon, you may have the upgraded sound system which uses a factory amp. i'm not sure if you need something to trigger the amp to turn on to get sound? in fact it may not even just be a +12v to the amp, it might be a CAN-BUS signal. like you may need something along these lines: http://amzn.to/2mbgffR just a possibility anyway... EDIT, after some quick research: if you do have the upgraded sound system, the factory amp supposedly uses a bus signal from the headunit to adjust volume, so you would need an interface similar to what i linked to work with that. Last edited by theksmith; 03-05-2017 at 07:14 AM. JK Newbie Thread Starter
Join Date: Feb 2017 Location: Troy, ID Posts: 13 Likes: 0 Received 0 Likes on 0 Posts Thanks, this makes sense. I think I will run wires directly out to the speakers and bypass the oem system. JK Newbie Thread Starter
Join Date: Feb 2017 Location: Troy, ID Posts: 13 Likes: 0 Received 0 Likes on 0 Posts Any idea where the speaker wires come into this oem amp so I don't have to run new wire all the way out? JK Newbie Thread Starter
Join Date: Feb 2017 Location: Troy, ID Posts: 13 Likes: 0 Received 0 Likes on 0 Posts |
2011 jeep wrangler radio wiring diagram
Related Posts
Copyright © 2024 en.apacode Inc.
